aca 500+ / cf with 1.3 as boot card
Is it possible to boot a CF card with WB1.3 installed from the `Boot Card' slot? So far, I have tried formatting a 4GB CF card into two partitions (DH0,DH1) and copied WB 1.3 to DH0. I formatted in...
View ArticleWhat floppies to buy
Hi All, I want to buy some blank floppies for my A1200 but don't know what to buy. Blank DS/DD disks? Thanks Brad Hansen
View Articleamiga keyboard and e box key v 2.0
amiga 1200 tower with this interfave http://amigakit.leamancomputing.com/...roducts_id=541. interface works with old pc ps2 keyboard. I got this item http://www.ebay.co.uk/itm/253244310443...
View ArticleProblem with KS3.1 and Amiga 3000
I recently purchased KS3.1 roms to upgrade my A3000 that came with KS2.04. For the KS2.04 ROMS, ROM0 is in U181 and ROM1 is in U180 (marking of ROM0 and ROM1 on the motheboard is wrong.. or markings on...
View Articledisk drive dead as the dodo
I may have done something stupid... again. I had amiga 1200 half naked. wanted to test out floppy drive which had always been a solid, good and nice healthy drive! anyway I forgot that the pcb of the...
View ArticleG-Force 040 combo A2000 undocumented jumpers
Does anyone have the info on this squirreled away somewhere? The original GVP manual specifically addresses the jumper question and says to contact them if you need the info. Just hoping... I have a...
View ArticleA4000D u212 gal
Would anyone know where I could purchase a programmed u212 gal 22v10b? I thought I'd try and repair this board one more time. I probably should just put amibian on a Raspberry Pi and stop torturing...
View ArticleBad PPC?
I think, but I am not sure that my PPC is no longer working. Here are the symptoms: * When it boots up it locks when it should put the picture in the background. I'm using warp datatypes. * If I boot...
View ArticleNEW HDMI Zorro Graphics card by MNT
Check out this new graphics card by MNT https://youtu.be/HkLu4QZPdhw Order here http://mntshop.bigcartel.com/product...tch-2-preorder
View ArticleA4000 wont boot while Cd drive attached
I know there are issues such as tray wont eject pushing button but at least this system booted to workbench. Set up with warp engine scsi controller and it did read cds . Now as long as the drive is...
View ArticleClik here to view.
Can anyone tell which A500 modification this is? (Noob)
Hi there Amiga enthusiasts, I just started collecting and working on some Amigas 500, so I probably have a noob question: I have one dead A500 rev 5 board (most likely ram chip error) but I also...
View ArticleA4000T motherboard RAM
A4000T with 16MB RAM, 4 x 4MB in motherboard sockets, standard A3640 rev3.2, CV-64/3D (The VirgeDX / DCE version), X-Surf100 w/RapidRoad. Everything is AOK on a fresh install of 3.1. After setting up...
View ArticleClik here to view.
ACACLOCK command issues with ACA1221EC accelerator
Has anyone had any success using the ACAclock command with an ACA1221EC accelerator board? Just purchased the ACA500Plus and the ACA1221EC from Individual Computers, for my A500 plus. The product pages...
View ArticleClik here to view.
paula plcc pinout
couldnt find paula plcc pinout, so here is some of it. I've modified pdf from some other chip. the pins with ?? are probably Vcc, Vss, GND? Attached Files PAULA_PLCC.odg.zip (12.1 KB)
View ArticleNeed Help with A3000 RAM Install
I have 16 MB worth of ZIP chips, enough to populate the entire motherboard. I put 4 MB in first and booted the computer to make sure it worked. I then put another 4 MB in and booted again, computer...
View ArticleScan Doubler
Hi all I am going to get a Scandoubler from eBay well what I need to know is as for the memory does it use any up? At the moment I see on my screen 1.7xxx and I also have 32Mb of fast ram. Thank a lot,...
View ArticleCF card to A2000/A3000
Can I use my CF 4GB card to my A2000(with GVP hc+8 series ii)or my A3000? I can use the card easily to the A1200 with IDE to CF adapter.
View ArticleA608 problem
I have a problem with the A608 RAM expansion for Amiga 600. It used to work, but after some fiddling with leaked caps, and other stuff, it causes A600 to constantly reboot. what could it be?
View ArticleIssues with the BPPC2 and GND Plane
Many maybe know that I bought 2 PCBs from Phase5 for BPPCs. I got them this easter. but never really done anything with them. after Amiga32 I decided to finally move the components from my busted BPPC...
View ArticleApolo Turbo 030
Hi all, I got my Amiga 1200 back out and I Installed from new Workbench3.1. BUT I lost my original Apollo Turbo 030/40 Mhz Startup-Sequence commands. Has any one got these please? TIA, Mike.
View Article